Pay in installments of $17.65 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 18 - Jul 23
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
ZCD31Main Range of product OsiSense XC Series name Standard compact Product or component type Limit switch body Device short name ZCD Design Compact Body type Fixed Associated head ZCE65 ZCE02 ZCE27 ZCE14 ZCE06 ZCE66 ZCE63 ZCE21 ZCE13 ZCE05 ZCE28 ZCE01 ZCE64 ZCE11 ZCE10 ZCEH2 ZCE62 ZCE08 ZCE07 ZCE29 ZCE67 ZCEH0 ZCE24 ZCE09 Body material Zamak Number of poles 3 Contacts type and composition 1 NC + 2 NO Contact operation Snap action Complementary Associated
Main
| Range of product | OsiSense XC |
| Series name | Standard compact |
| Product or component type | Limit switch body |
| Device short name | ZCD |
| Design | Compact |
| Body type | Fixed |
| Associated head | ZCE65 ZCE02 ZCE27 ZCE14 ZCE06 ZCE66 ZCE63 ZCE21 ZCE13 ZCE05 ZCE28 ZCE01 ZCE64 ZCE11 ZCE10 ZCEH2 ZCE62 ZCE08 ZCE07 ZCE29 ZCE67 ZCEH0 ZCE24 ZCE09 |
| Body material | Zamak |
| Number of poles | 3 |
| Contacts type and composition | 1 NC + 2 NO |
| Contact operation | Snap action |
Complementary
| Associated connection component | ZCDEG11 ZCDEF12 ZCDEN12 ZCDEP16 ZCDEP20 ZCDEG13 |
| Electrical connection | Screw-clamp terminals, clamping capacity: 1 x 0.34...2 x 0.75 mm² |
| Contacts insulation form | Zb |
| Contacts material | Silver plated contacts |
| Positive opening | With |
| Minimum actuation speed | 0.01 m/s |
| Contact code designation | R300, DC-13 (Ue = 250 V), Ie = 0.1 A conforming to EN/IEC 60947-5-1 appendix A C300, AC-15 (Ue = 240 V), Ie = 0.75 A conforming to EN/IEC 60947-5-1 appendix A |
| [Ui] rated insulation voltage | 300 V conforming to UL 508 300 V conforming to CSA C22.2 No 14 400 V (pollution degree 3) conforming to IEC 60947-1 |
| [Uimp] rated impulse withstand voltage | 4 kV IEC 60664 4 kV IEC 60947-1 |
| Short-circuit protection | 6 A cartridge fuse, type gG |
| Electrical durability | 5000000 cycles, DC-13 120 V, 2 W, operating rate <60 cyc/mn, load factor: 0.5 conforming to IEC 60947-5-1 appendix C 5000000 cycles, DC-13 24 V, 4 W, operating rate <60 cyc/mn, load factor: 0.5 conforming to IEC 60947-5-1 appendix C 5000000 cycles, DC-13 48 V, 3 W, operating rate <60 cyc/mn, load factor: 0.5 conforming to IEC 60947-5-1 appendix C |
| Width | 31 mm |
| Height | 65 mm |
| Depth | 30 mm |
Environment
| Product compatibility | XCKD |
| Ambient air temperature for operation | -25…70 °C |
| Ambient air temperature for storage | -40…70 °C |
Offer Sustainability
| Sustainable offer status | Green Premium product |
| REACh Regulation | REACh Declaration |
| EU RoHS Directive | Pro-active compliance (Product out of EU RoHS legal scope) EU RoHS Declaration |
| Mercury free | Yes |
| RoHS exemption information | Yes |
| Environmental Disclosure | Product Environmental Profile |
| Circularity Profile | No need of specific recycling operations |
Contractual warranty
| Warranty | 18 months |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.6 ★★★★★
Based on 19 reviews
Sort
Product Reviews
★★★★★ 5
Saves So Much Time, Perfect Fit On Mercruiser Pre-Alpha Outdrive.
This is a very useful kit. Perfect fit to exchange and align the gimbal bearing on a Mercruiser MR/Pre-Alpha Outdrive. The metal rods are strong and well machined to fit the gimbal bearing and the template lines up great with the housing studs. The overall production quality is very good. Great value because the tools are very durable but for me the biggest value is the time saved. I had the bearing out in about 10 minutes. The ability to line up the bearing before attempting to attach the outdrive upper gear unit is very convenient and saves so much time. This are simple tools, very easy to use.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 1, 2026
★★★★★ 5
Easy to use
Works great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 9, 2026
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023